Ti6Al4V powder — supplier & RFQ
A widely used titanium alloy powder for lightweight structural AM parts where strength-to-weight performance matters.
- PSD15–45 µm · 15–53 µm · 45–105 µm
- ProcessLPBF · EBM · DED
- List priceUS$100–225/kg
- Min. pack1 kg
- Grade
- Ti64 · Grade 5
- Particle size
- 15–45 µm · 15–53 µm · 45–105 µm
- Processes
- LPBF · EBM · DED
- List price
- US$100–225/kg
- Samples
- Paid · from 1 kg
- Packaging
- Aluminium-foil bag · 1 kg sealed pack · Drum
- Lot documents
- Lot-specific COA · Particle-size report · Safety data sheet · Chemistry and interstitial report
Ti6Al4V powder applications by industry
| Industry | Typical parts | Why Ti6Al4V | Specify in your RFQ |
|---|---|---|---|
| Aerospace and space Guide → | Brackets, fittings, housings, satellite and UAV structures | High strength-to-weight with good fatigue after HIP and machining | Interstitial limits, HIP and heat treatment, machining allowance, governing specification such as ASTM F2924 |
| Robotics and automation Guide → | Robot arm brackets, end effectors, lightweight joints | Lower moving mass than steel with high stiffness per weight | Load cases, bearing and thread interfaces, surface finish |
| Motorsport and performance automotive | Uprights, brackets, exhaust and turbo-side components | Weight saving and corrosion resistance where cost allows titanium | Fatigue requirement, operating temperature, post-processing route |
| Marine and chemical | Pump and valve parts, seawater-wetted hardware | Very good resistance to chlorides and seawater | Media, temperature, crevice geometry, finished-surface condition |
Designations
- Ti-6Al-4V
- Ti64
- Grade 5
- UNS R56400
- TC4
Use Ti6Al4V, Ti-6Al-4V, Ti64, or Grade 5 in international RFQs. Pair the regional TC4 designation with the governing chemistry rather than assuming equivalence.
Particle size and powder properties
- Standard cuts
- 15–45 µm · 15–53 µm · 45–105 µm
- Processes
- LPBF · EBM · DED
- Typical uses
- Lightweight brackets and housings · Structural AM parts · Corrosion-resistant hardware
| Property | Typical value | Note |
|---|---|---|
| D10 | ≥15 µm | Laser-distribution screening value |
| D50 | 30–40 µm | Grade-specific screening window |
| D90 | ≤63 µm | Grade-specific screening window |
| Sphericity | ≥0.90 | Method to be confirmed |
| Apparent density | ≥2.4 g/cm³ | Test method to be confirmed |
| Tap density | ≥2.8 g/cm³ | Test method to be confirmed |
| Flow | ≤35 s/50 g | Method and conditioning to be confirmed |
LPBF screening window. Measured values are reported on the lot COA.
Chemical composition
| Ti | Al | V | Fe | C | O | N | H |
|---|---|---|---|---|---|---|---|
| Balance | 5.50–6.75 | 3.50–4.50 | ≤0.30 | ≤0.08 | ≤0.12 | ≤0.03 | ≤0.015 |
wt.% · Typical partner-plant datasheet limits, wt.%. For reference, ASTM F2924 allows up to 0.20 wt% oxygen for Grade 5; the partner-plant oxygen limit listed here is tighter. The quoted lot COA governs.
Typical mechanical properties
| Condition | Temperature | Tensile | Yield | Elongation |
|---|---|---|---|---|
| Heat treated | Room temperature | ≥950 MPa | ≥900 MPa | ≥10% |
Partner-plant datasheet values for LPBF test bars at room temperature unless stated. Printed-part properties depend on machine, parameters, orientation, and post-processing.
Documents and packaging
Supplied with each lot
- Lot-specific COA
- Particle-size report
- Safety data sheet
- Chemistry and interstitial report
State the Grade 5, UNS, or customer chemistry basis, including interstitial limits and any program-specific revision.
Packaging
- Aluminium-foil bag — very small quantities and paid samples
- 1 kg sealed pack — minimum standard package
- Drum — production lots
Samples are paid. The smallest standard pack is 1 kg.
Export
Export & compliance →Titanium and titanium-alloy powders can fall under China's dual-use export controls (list entry 1C111). If a Titanium Ti6Al4V order is covered, it needs an export licence before shipment — samples included. The quotation states whether a licence is needed and what we need from you: end user, end use and destination. Read buying titanium powder from China for the licence steps and timing.
Price
List price · EXW China
US$100–225/kg
Our list price for LPBF cuts (15–45 µm or 15–53 µm), per kg, EXW China, from 1 kg. It is set at 80–90% of the public list prices of mainstream suppliers checked in October 2026. Other particle-size cuts are priced by agreement; packing and freight are quoted separately. Your written quotation from our official corporate email confirms the price, lead time and terms for your quantity, particle size and documents.
Other titanium grades
| Powder | Particle size | Process |
|---|---|---|
| Ti6Al4V ELI powder | 15–45 µm · 15–53 µm · 45–105 µm | LPBF · EBM |
| TA1 titanium powder | 15–45 µm · 15–53 µm · 45–105 µm | LPBF · EBM |
| TA15 titanium powder | 15–53 µm · 45–105 µm | LPBF · EBM · DED |
Technical notes
- TC4 (Ti-6Al-4V) Grade 5/23 Titanium Powder for LPBF, EBM & DED
- Ti6Al4V vs CP titanium: strength or commercially pure titanium?
- Grade 23 vs Grade 5: when do lower interstitial limits matter?
- Additive Manufacturing Powder Suppliers and Manufacturers: Buyer Guide
- How to Sample an AM Metal Powder Lot for Reliable PSD Results
- Gas Atomized Metal Powder for Additive Manufacturing
- Powder Spreadability and Layer Density in LPBF: Buyer Specification Guide
- Metal Powder Flowability Tests for AM: Hall, Carney, and Rheology
- Metal Powder for 3D Printing: Alloys, Sizes, and Buying Guide